Abstract: | The coplanar wave guide is an attractive device in microwave integrated circuits due to its uniplanar nature, ease of fabrication and low production cost. Several attempts are already done to explore the radiating modes in coplanar wave guide transmission lines. Usually coplanar wave guides are excited by an SMA connector with its centre conductor connected to the exact middle of the centre strip and the outer ground conductor to the two ground strips. The mode excited on it is purely a bound mode. The E-field distribution in the two slots are out of phase and there for cancels at the far field. This thesis addresses an attempt to excite an in phase E-field distribution in the two slots of the co planar wave guide by employing a feed asymmetry, in order to get radiation from the two large slot discontinuities of the coplanar waveguide. The omni directional distribution of the radiating energy can be achieved by widening the centre strip.The first part of the thesis deals with the investigations on the resonance phenomena of conventional coplanar waveguides at higher frequency bands. Then an offset fed open circuited coplanar waveguide supporting resonance/radiation phenomena is analyzed. Finally, a novel compact co planar antenna geometry with dual band characteristics, suitable for mobile terminal applications is designed and characterized using the inferences from the above study. |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2553 |
Files | Size |
---|---|
Dyuthi-T0697.pdf | (16.44Mb) |
Abstract: | The thesis is the outcome of the experimental and theoretical investigations on a new compact drum-shaped microstrip antenna. A new compact antenna suitable for personal communication system(PCS), Global position System(GPS) and array applications is developed and analysed. The generalised cavity model and spatial fourier transform technique are suitably modified for the analysis of the antenna. The predicted results are compared with experimental results and excellent agreement is observed. The experimental work done by the author in related fields are incorporated as three appendices in this thesis. A single feed dual frequency microstrip antenne is presented in appendix A.Appendix B describes a new broadband dual frequeny microstrip antenna. The bandwidth enhancement effect of microstrip antennas through dielectric resonator loading is demonstarted in Appendix C. |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2166 |
Files | Size |
---|---|
Dyuthi-T0519.pdf | (6.749Mb) |
Abstract: | This thesis describes the development and analysis of an Isosceles Trapezoidal Dielectric Resonator Antenna (ITDRA) by realizing different DR orientations with suitable feed configurations enabling it to be used as multiband, dual band dual polarized and wideband applications. The motivation for this work has been inspired by the need for compact, high efficient, low cost antenna suitable for multi band application, dual band dual polarized operation and broadband operation with the possibility of using with MICs, and to ensure less expensive, more efficient and quality wireless communication systems. To satisfy these challenging demands a novel shaped Dielectric Resonator (DR) is fabricated and investigated for the possibility of above required properties by trying out different orientations of the DR on a simple microstrip feed and with slotted ground plane as well. The thesis initially discusses and evaluates recent and past developments taken place within the microwave industry on this topic through a concise review of literature. Then the theoretical aspects of DRA and different feeding techniques are described. Following this, fabrication and characterization of DRA is explained. To achieve the desired requirements as above both simulations and experimental measurements were undertaken. A 3-D finite element method (FEM) electromagnetic simulation tool, HFSSTM by Agilent, is used to determine the optimum geometry of the dielectric resonator. It was found to be useful in producing approximate results although it had some limitations. A numerical analysis technique, finite difference time domain (FDTD) is used for validating the results of wide band design at the end. MATLAB is used for modeling the ITDR and implementing FDTD analysis. In conclusion this work offers a new, efficient and relatively simple alternative for antennas to be used for multiple requirements in the wireless communication system. |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2761 |
Files | Size |
---|---|
Dyuthi-T0784.pdf | (11.24Mb) |
Abstract: | The practical applications of microstrip antennas for mobile systems are in portable or pocket-size equipment and in vehicles. Antennas for VHFIUHF handheld portable equipment, such as pagers, portable telephones and transceivers, must naturally be small in size, light in weight and compact in structure. There is a growing tendency for portable equipment to be made smaller and smaller as the demand for personal communication rapidly increases, and the development of very compact hand-held units has become urgent.In this thesis work, main aim is to develop a more and more reduced sized microstrip patch antenna. It is well known that the smaller the antenna size, the lower the antenna efficiency. During the period of work, three different compact circular sided microstrip patches are developed and analysed, which have a significant size reduction compared to standard circular disk antenna (the most compact one of the basic microstrip patch configurations), without much deterioration of its properties like gain, bandwidth and efficiency. In addition to this the interesting results, dual port operation and circular polarization are also observed for some typical designs of these patches. These make the patches suitable for satellite and mobile communication systems.The theoretical investigations are carried out on these compact patches. The empirical relations are developed by modifying the standard equations of rectangular and circular disk microstrip patches, which helps to predict the resonant frequencies easily. |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2794 |
Files | Size |
---|---|
Dyuthi-T0815.pdf | (8.400Mb) |
Description: | Department of Elecctronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2118 |
Files | Size |
---|---|
Dyuthi-T0392.pdf | (10.85Mb) |
Abstract: | The thesis explores the outcome of the exhaustive theoretical and experimental investigations performed on Octagonal Microstrip Antenna configurations. Development of the MATLAB TM backed 3D-Conformal Finite Difference Time Domain (CFDTD)Modeller for the numerical computation of the radiation characteristics of the antenna is the theme of the work. The predicted results are verified experimentally and by IE3D TM simulation. The influence of the patch dimensions,feed configurations,feed dimensions and feed positions upon the radiation performance of the antenna is studied in detail. Octagonal Microstrip Antenna configurations suitable for Mobile-Bluetooth application is dealt in detail. A simple design formula for the regular Octagonal geometry is also presented. A compact planar multi band antenna for GPS/DCS/2.4/5.8GHz WLAN application is included as appendix A. Planar near field measurement technique is explained in appendix B. |
Description: | Department of Electroncis, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2167 |
Files | Size |
---|---|
Dyuthi-T0518.pdf | (14.48Mb) |
Abstract: | The thesis is the outcome of the experimental and theoretical Investigations on novel feeding techniques for bandwidth enhancement of microstrip patches. The new feeding techniques provide bandwidth enhancement without deteriorating the radiation characteristics of the antenna. The antenna is analysed using finite Difference Time Domain (FDTD) method. The predicated results are compared with the experimental results and excellent agreement is observed. The results are also verified using IE3D simulation software. The antenna is suitable for personal and broadband communications. |
Description: | Dept.of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2116 |
Files | Size |
---|---|
Dyuthi-T0393.pdf | (10.18Mb) |
Abstract: | Antennas, the key element in wireless communication devices had undergone amazing developments especially in the direction of compactness and safety aspects. In the last two decades, the use of the cellular phones has become the most popular mode of communication across the globe. At the same time, the concerns about the radiation effects have increased in the general public. The main concern of this thesis is to develop a mobile antenna which gives reduced RF interference to the user. The reduction of the power absorbed by the user can tremendously avoid any possible health hazards. The radiation characteristic of a monopole antenna is modified with good radiation characteristics suitable for a mobile handset. The modification is implemented by using different resonating structures which provides reduced radiation along one direction. The direction of less radiation can be changed by modifying the planar antenna structure to a ground folded antenna. This modified structure with excellent radiation characteristic is suitable for modern wireless handheld devices with less user RF interference. Specific Absorption Rate (SAR) is an important parameter for mobile handset. The SAR is estimated for the newly developed antenna for different conditions and discussed in this thesis. |
Description: | Department of Electronics, Cochin University of Science And Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3710 |
Files | Size |
---|---|
Dyuthi-T1668.pdf | (17.01Mb) |
Abstract: | The 20th century witnessed the extensive use of microwaves in industrial, scientific and medical fields. The major hindrance to many developments in the ISM field is the lack of knowledge about the effect of microwaves on materials used in various applications. The study of the interaction of microwaves with materials demanded the knowledge of the dielectric properties of these materials. However, the dielectric properties of many of these materials are still unknown or less studied. This thesis is an effort to shed light into the dielectric properties of some materials which are used in medical, scientific and industrial fields. Microwave phantoms are those materials used in microwave simulation applications. Effort has been taken to develop and characterize low cost, eco-friendly phantoms from Biomaterials and Bioceramics. The interaction of microwaves with living tissues paved way to the development of materials for electromagnetic shielding. Materials with good conductivity/absorption properties could be used for EMI shielding applications. Conducting polymer materials are developed and characterized in this context. The materials which are developed and analyzed in this thesis are Biomaterials, Bioceramics and Conducting polymers. The use of materials of biological origin in scientific and medical applications provides an eco-friendly pathway. The microwave characterization of the materials were done using cavity material perturbation method. Low cost and ecofriendly biomaterial films were developed from Arrowroot and Chitosan. The developed films could be used in applications such as microwave phantom material, capsule material in pharmaceutical applications, trans-dermal patch material and eco-friendly Band-Aids. Bioceramics with better bioresorption and biocompatibility were synthesized. Bioceramics such as Hydroxyapatite, Beta tricalcium phosphate and Biphasic Calcium Phosphate were studied. The prepared bioceramics could be used as phantom material representing Collagen, Bone marrow, Human abdominal wall fat and Human chest fat. Conducting polymers- based on Polyaniline, are developed and characterized. The developed materials can be used in electromagnetic shielding applications such as in anechoic chambers, transmission cables etc |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/4695 |
Files | Size |
---|---|
Dyuthi-T1826.pdf | (11.01Mb) |
Abstract: | The thesis explores the area of still image compression. The image compression techniques can be broadly classified into lossless and lossy compression. The most common lossy compression techniques are based on Transform coding, Vector Quantization and Fractals. Transform coding is the simplest of the above and generally employs reversible transforms like, DCT, DWT, etc. Mapped Real Transform (MRT) is an evolving integer transform, based on real additions alone. The present research work aims at developing new image compression techniques based on MRT. Most of the transform coding techniques employ fixed block size image segmentation, usually 8×8. Hence, a fixed block size transform coding is implemented using MRT and the merits and demerits are analyzed for both 8×8 and 4×4 blocks. The N2 unique MRT coefficients, for each block, are computed using templates. Considering the merits and demerits of fixed block size transform coding techniques, a hybrid form of these techniques is implemented to improve the performance of compression. The performance of the hybrid coder is found to be better compared to the fixed block size coders. Thus, if the block size is made adaptive, the performance can be further improved. In adaptive block size coding, the block size may vary from the size of the image to 2×2. Hence, the computation of MRT using templates is impractical due to memory requirements. So, an adaptive transform coder based on Unique MRT (UMRT), a compact form of MRT, is implemented to get better performance in terms of PSNR and HVS The suitability of MRT in vector quantization of images is then experimented. The UMRT based Classified Vector Quantization (CVQ) is implemented subsequently. The edges in the images are identified and classified by employing a UMRT based criteria. Based on the above experiments, a new technique named “MRT based Adaptive Transform Coder with Classified Vector Quantization (MATC-CVQ)”is developed. Its performance is evaluated and compared against existing techniques. A comparison with standard JPEG & the well-known Shapiro’s Embedded Zero-tree Wavelet (EZW) is done and found that the proposed technique gives better performance for majority of images |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/4740 |
Files | Size |
---|---|
Dyuthi-T1838.pdf | (11.99Mb) |
Abstract: | Biometrics deals with the physiological and behavioral characteristics of an individual to establish identity. Fingerprint based authentication is the most advanced biometric authentication technology. The minutiae based fingerprint identification method offer reasonable identification rate. The feature minutiae map consists of about 70-100 minutia points and matching accuracy is dropping down while the size of database is growing up. Hence it is inevitable to make the size of the fingerprint feature code to be as smaller as possible so that identification may be much easier. In this research, a novel global singularity based fingerprint representation is proposed. Fingerprint baseline, which is the line between distal and intermediate phalangeal joint line in the fingerprint, is taken as the reference line. A polygon is formed with the singularities and the fingerprint baseline. The feature vectors are the polygonal angle, sides, area, type and the ridge counts in between the singularities. 100% recognition rate is achieved in this method. The method is compared with the conventional minutiae based recognition method in terms of computation time, receiver operator characteristics (ROC) and the feature vector length. Speech is a behavioural biometric modality and can be used for identification of a speaker. In this work, MFCC of text dependant speeches are computed and clustered using k-means algorithm. A backpropagation based Artificial Neural Network is trained to identify the clustered speech code. The performance of the neural network classifier is compared with the VQ based Euclidean minimum classifier. Biometric systems that use a single modality are usually affected by problems like noisy sensor data, non-universality and/or lack of distinctiveness of the biometric trait, unacceptable error rates, and spoof attacks. Multifinger feature level fusion based fingerprint recognition is developed and the performances are measured in terms of the ROC curve. Score level fusion of fingerprint and speech based recognition system is done and 100% accuracy is achieved for a considerable range of matching threshold |
Description: | Department of Electronics Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3547 |
Files | Size |
---|---|
Dyuthi-T1515.pdf | (7.138Mb) |
Abstract: | Breast cancer is the most common non - skin malignancy in women and a leading cause of female morality. A potentially important strategy for reducing this menace is the detection at an early stage . The invention of non-invasive and non-ionizing microwave technique, to reveal the internal structure of biological objects was a break through in the field of medical diagnostics. Electrical properties of biological tissues and their interaction with electromagmetic waves have direct impact on human life. This thesis focuses on theoretical and experimental investigations of active microwave imaging techniques for breast cancer detection. |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2124 |
Files | Size |
---|---|
Dyuthi-T0394.pdf | (13.57Mb) |
Abstract: | In this thesis, different techniques for image analysis of high density microarrays have been investigated. Most of the existing image analysis techniques require prior knowledge of image specific parameters and direct user intervention for microarray image quantification. The objective of this research work was to develop of a fully automated image analysis method capable of accurately quantifying the intensity information from high density microarrays images. The method should be robust against noise and contaminations that commonly occur in different stages of microarray development. |
Description: | Department of Electronics Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3993 |
Files | Size |
---|---|
Dyuthi-T1802.pdf | (17.22Mb) |
Abstract: | Breast cancer detection is an important social requisite as it is the leading cause of death due to cancer among women. The mortality rate of breast cancer is second among all cancers. The cause for breast cancer is not known to date and early detection & treatment are the only means to reduce breast cancer related deaths. Mammography is the main radiological tool that is employed for identifying breast cancer at the earliest stage. Computer aided techniques have great relevance in detection of abnormalities from mammographic images, as often the features associated with various abnormalities are difficult to detect and might be missed by even trained radiologists. In addition, when screening mammography is employed, a large number of mammographic images need to be checked for signs of abnormality, justifying the use of computer aided diagnosis. Three problems are addressed in this thesis: delineation of the pectoral muscle region by properly identifying the pectoral muscle boundary, detection of architectural distortion and enhancement of microcalcification features in the mammographic images. Two novel methods were developed for identifying the pectoral muscle boundary from mediolateral oblique view mammograms that employed multiscale decomposition and local segmentation. The breast area is extracted after this step following the removal of the Pectoral muscle region. The breast abnormalities are searched for in this region. Architectural distortion is the most commonly missed abnormality in mammograms. A novel method for detecting architectural distortion is proposed in this thesis that employs geometrical features obtained from selected edge structures in the mammographic image. These features are used to train a feedforward neural network classifier initialized using metaheuristic algorithms for better classification. Microcalcification is another breast cancer symptom which is ii said to be the most commonly occurring. However the visibility of the microcalcification structures is often poor, especially when they are located in dense parenchymal tissues. Therefore an algorithm is proposed to enhance such features, employing the singularities, viz. zero-crossings and modulus maxima of coefficients obtained after computing the contourlet transform of the mammographic image. Contourlet transform is employed for the directional information it provides. |
URI: | http://dyuthi.cusat.ac.in/purl/5149 |
Files | Size |
---|---|
Dyuthi-T2183.pdf | (10.07Mb) |
Abstract: | Fourier transform methods are employed heavily in digital signal processing. Discrete Fourier Transform (DFT) is among the most commonly used digital signal transforms. The exponential kernel of the DFT has the properties of symmetry and periodicity. Fast Fourier Transform (FFT) methods for fast DFT computation exploit these kernel properties in different ways. In this thesis, an approach of grouping data on the basis of the corresponding phase of the exponential kernel of the DFT is exploited to introduce a new digital signal transform, named the M-dimensional Real Transform (MRT), for l-D and 2-D signals. The new transform is developed using number theoretic principles as regards its specific features. A few properties of the transform are explored, and an inverse transform presented. A fundamental assumption is that the size of the input signal be even. The transform computation involves only real additions. The MRT is an integer-to-integer transform. There are two kinds of redundancy, complete redundancy & derived redundancy, in MRT. Redundancy is analyzed and removed to arrive at a more compact version called the Unique MRT (UMRT). l-D UMRT is a non-expansive transform for all signal sizes, while the 2-D UMRT is non-expansive for signal sizes that are powers of 2. The 2-D UMRT is applied in image processing applications like image compression and orientation analysis. The MRT & UMRT, being general transforms, will find potential applications in various fields of signal and image processing. |
Description: | Division of Electronics Engineering,Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2688 |
Files | Size |
---|---|
Dyuthi-T0740.pdf | (6.733Mb) |
Abstract: | This thesis presents the results of an investigation conducted for the development of a new type of feed horn antenna called "Simulated Scalar Feed". A schematic presentation of the work is given below. A review of the past important work done in the field of conventional/multimode electromagnetic horn antennas is presented in the first part of the second chapter. The work carried out on corrugated horns and surfaces are included in the second part of the review. In the third part, work on dielectric and dielectric loaded metal horns are reviewed. In all the parts of the review, special emphasis is given to theoretical design considerations. The methodology adopted for the experimental investigations is presented in the third chapter. The instrumentation utilized and thThis thesis presents the results of an investigation conducted for the development of a new type of feed horn antenna called "Simulated Scalar Feed". A schematic presentation of the work is given below. A review of the past important work done in the field of conventional/multimode electromagnetic horn antennas is presented in the first part of the second chapter. The work carried out on corrugated horns and surfaces are included in the second part of the review. In the third part, work on dielectric and dielectric loaded metal horns are reviewed. In all the parts of the review, special emphasis is given to theoretical design considerations. The methodology adopted for the experimental investigations is presented in the third chapter. The instrumentation utilized and the details of fabrication ofe details of fabrication of the new simulated scalar feed are described. The method of measurements of radiation characteristics of the antenna are also explained in this chapter. In the fourth chapter the outcome of the experimental results of the investigations carried out on horn antennas fabricated with different physical dimensions and different parameters for the E—plane boundary walls are highlighted. The theoretical explanation used to explain the experimental results is given in the fifth chapter of the thesis. A comparison between the experimental and the theoretical results is also presented in this chapter. In chapter six, the conclusions drawn from the experimental as well as the theoretical investigations are discussed. The advantages and features of the newly developed simulated scalar feed is examined in this chapter. Scope of further investigations in this field is also discussed at the end of this chapter. |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3199 |
Files | Size |
---|---|
Dyuthi-T1173.pdf | (2.068Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5188 |
Files | Size |
---|---|
Dyuthi T-2223.pdf | (4.427Mb) |
Abstract: | The author presents the development of a new dielectric resonator antenna(DRA) suitable for wideband wireless communication applications.The design comprises of a simple cylindrical dielectric resonator (DR) and a microstrip feed, in a low radiation-Q structure,enabling wide impedance bandwidth.The radiation pattern is conical shaped,resulted from thew low-Q structure.Dielectric constant of the DR,its dimensions and topological parameters of the feed line are the major design parameters of the antenna.By proper selection of these parameters,the DRA can be operated over a wideband width covering multiple wireless applications.The antenna is simulated using Ansoft HFSS TM and measured using HP 8510C vector network analyser.Some of the measured results are confirmed by using the Finite Difference Time Domain(FDTD) technique implemented in MATLAB. |
Description: | Department of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2892 |
Files | Size |
---|---|
Dyuthi-T0889.pdf | (10.07Mb) |
Abstract: | The measurement of global precipitation is of great importance in climate modeling since the release of latent heat associated with tropical convection is one of the pricipal driving mechanisms of atmospheric circulation.Knowledge of the larger-scale precipitation field also has important potential applications in the generation of initial conditions for numerical weather prediction models Knowledge of the relationship between rainfall intensity and kinetic energy, and its variations in time and space is important for erosion prediction. Vegetation on earth also greatly depends on the total amount of rainfall as well as the drop size distribution (DSD) in rainfall.While methods using visible,infrared, and microwave radiometer data have been shown to yield useful estimates of precipitation, validation of these products for the open ocean has been hampered by the limited amount of surface rainfall measurements available for accurate assessement, especially for the tropical oceans.Surface rain fall measurements(often called the ground truth)are carried out by rain gauges working on various principles like weighing type,tipping bucket,capacitive type and so on.The acoustic technique is yet another promising method of rain parameter measurement that has many advantages. The basic principle of acoustic method is that the droplets falling in water produce underwater sound with distinct features, using which the rainfall parameters can be computed. The acoustic technique can also be used for developing a low cost and accurate device for automatic measurement of rainfall rate and kinetic energy of rain.especially suitable for telemetry applications. This technique can also be utilized to develop a low cost Disdrometer that finds application in rainfall analysis as well as in calibration of nozzles and sprinklers. This thesis is divided into the following 7 chapters, which describes the methodology adopted, the results obtained and the conclusions arrived at. |
Description: | Dept.of Electronics, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2171 |
Files | Size |
---|---|
Dyuthi-T0523.pdf | (9.338Mb) |
Abstract: | Ship recycling has been considered as the best means to dispose off an obsolete ship. The current state of art of technology combined with the demands of sustainable developments from the global maritime industrial sector has modified the status of erstwhile ‘ship breaking’ involving ship scrap business to a modern industry undertaking dismantling of ships and recycling/reusing the dismantled products in a supply chain of pre owned product market by following the principles of recycling. Industries will have to formulate a set of best practices and blend them with the engineering activities for producing better quality products, improving the productivity and for achieving improved performances related to sustainable development. Improved performance by industries in a sustainable development perspective is accomplished only by implementing the 4E principles, ie.,. ecofriendliness, engineering efficiency, energy conservation and ergonomics in their core operations. The present study has done a comprehensive investigation into various ship recycling operations for formulating a set of best practices.Being the ultimate life cycle stage of a ship, ship recycling activities incorporate certain commercial procedures well in advance to facilitate the objectives of dismantling and recycling/reusing of various parts of the vessel. Thorough knowledge regarding these background procedures in ship recycling is essential for examining and understanding the industrial business operations associated with it. As a first step, the practices followed in merchant shipping operations regarding the decision on decommissioning have been and made available in the thesis. Brief description about the positioning methods and important preparations for the most feasible ship recycling method ie.,. beach method have been provided as a part of the outline of the background information. Available sources of guidelines, codes and rules & regulations for ship recycling have been compiled and included in the discussion.Very brief summary of practices in major ship recycling destinations has been prepared and listed for providing an overview of the global ship recycling activities. The present status of ship recycling by treating it as a full fledged engineering industry has been brought out to establish the need for looking into the development of the best practices. Major engineering attributes of ship as a unique engineering product and the significant influencing factors on her life cycle stage operations have been studied and added to the information base on ship recycling. Role of ship recycling industry as an important player in global sustainable development efforts has been reviewed by analysing the benefits of ship recycling. A brief synopsis on the state of art of ship recycling in major international ship recycling centres has also been incorporated in the backdrop knowledgebase generation on ship recycling processes.Publications available in this field have been reviewed and classified into five subject categories viz., Infrastructure for recycling yards and methods of dismantling, Rules regarding ship recycling activities, Environmental and safety aspects of ship recycling, Role of naval architects and ship classification societies, Application of information technology and Demand forecasting. The inference from the literature survey have been summarised and recorded. Noticeable observations in the inference include need of creation of a comprehensive knowledgebase on ship recycling and its effective implementation in the industry and the insignificant involvement of naval architects and shipbuilding engineers in ship recycling industry. These two important inferences and the message conveyed by them have been addressed with due importance in the subsequent part of the present study.As a part of the study the importance of demand forecasting in ship recycling has been introduced and presented. A sample input for ship recycling data for implementation of computer based methods of demand forecasting has been presented in this section of the thesis.The interdisciplinary nature of engineering processes involved in ship recycling has been identified as one of the important features of this industry. The present study has identified more than a dozen major stake holders in ship recycling having their own interests and roles. It has also been observed that most of the ship recycling activities is carried out in South East Asian countries where the beach based ship recycling is done in yards without proper infrastructure support. A model of beach based ship recycling has been developed and the roles, responsibilities and the mutual interactions of the elements of the system have been documented as a part of the study Subsequently the need of a generation of a wide knowledgebase on ship recycling activities as pointed out by the literature survey has been addressed. The information base and source of expertise required to build a broad knowledgebase on ship recycling operations have been identified and tabulated. Eleven important ship recycling processes have been identified and a brief sketch of steps involved in these processes have been examined and addressed in detail. Based on these findings, a detailed sequential disassembly process plan of ship recycling has been prepared and charted. After having established the need of best practices in ship recycling initially, the present study here identifies development of a user friendly expert system for ship recycling process as one of the constituents of the proposed best practises. A user friendly expert system has been developed for beach based ship recycling processes and is named as Ship Recycling Recommender (SRR). Two important functions of SRR, first one for the ‘Administrators’, the stake holders at the helm of the ship recycling affairs and second one for the ‘Users’, the stake holders who execute the actual dismantling have been presented by highlighting the steps involved in the execution of the software. The important output generated, ie.,. recommended practices for ship dismantling processes and safe handling information on materials present onboard have been presented with the help of ship recycling reports generated by the expert system. A brief account of necessity of having a ship recycling work content estimation as part of the best practices has been presented in the study. This is supported by a detailed work estimation schedule for the same as one of the appendices.As mentioned earlier, a definite lack of involvement of naval architect has been observed in development of methodologies for improving the status of ship recycling industry. Present study has put forward a holistic approach to review the status of ship recycling not simply as end of life activity of all ‘time expired’ vessels, but as a focal point of integrating all life cycle activities. A new engineering design philosophy targeting sustainable development of marine industrial domain, named design for ship recycling has been identified, formulated and presented. A new model of ship life cycle has been proposed by adding few stages to the traditional life cycle after analysing their critical role in accomplishing clean and safe end of life and partial dismantling of ships. Two applications of design for ship recycling viz, recyclability of ships and her products and allotment of Green Safety Index for ships have been presented as a part of implementation of the philosophy in actual practice. |
Description: | Dept of Ship Technology,Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2353 |
Files | Size |
---|---|
Dyuthi-T0626.pdf | (6.512Mb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.