Surendran,K P; Sebastian,M T; Mohanan, P; Mohanan,Jacob V(American Institute of Physics, 2005)
[+]
[-]
Abstract:
The effect of dopants with different valencies and ionic radii on the densification, structural
ordering, and microwave dielectric properties of Ba(Mg1t3Tazt3)O3 (BMT) is investigated. It is
found that dopants such as Sb,05, MnO, ZrO,, WO1, and ZnO improve the microwave dielectric
properties of BMT. Addition of trivalent dopants is detrimental to the cation ordering and dielectric
properties of BMT. A correlation between the microwave dielectric properties of BMT and ionic
radii of the dopant has been established. The variation of the dielectric properties of pure and doped
BMT at cryogenic temperatures is also discussed
The effect of glass additives on the densification , phase evolution, microstructure and microwave dielectric properties of Ba(Mg1;3
Ta2i3)03 (BMT) was investigated . Different weight percentages of quenched glass such as B203 , Si02, B203-SiO2, ZnO-B203,
5ZnO-2B2O3, Al203-SiO2, Na20-2B203.10H20, BaO-B203-SiO2, MgO-B203-SiO2, PbO-B203-SiO2 , ZnO-B203-SiO2 and
2MgO-Al203-5SiO2 were added to calcined BMT precursor . The sintering temperature of the glass -added BMT samples were
lowered down to 1300 °C compared to solid-state sintering where the temperature was 1650 °C. The formation of high temperature
satellite phases such as Ba5Ta4O15 and Ba7Ta6O22 were found to be suppressed by the glass addition . Addition of glass systems such
as B203, ZnO-B203, 5ZnO-2B203 and ZnO-B203-SiO2 improved the densification and microwave dielectric properties. Other
glasses were found to react with BMT to form low-Q phases which prevented densification . The microwave dielectric properties of
undoped BMT with a densification of 93 . 1 % of the theoretical density were Cr = 24 . 8, Tr = 8 ppm/°C and Q„ x f= 80,000 GHz. The
BMT doped with 1.0 wt% of B203 has Q„ x f = 124,700GHz, Cr = 24.2, and T f = -1.3 ppm /°C. The unloaded Q factor of 0.2 wt%
ZnO-B203-doped BMT was 136,500 GHz while that of 1.0 wt% of 5ZnO-2B203 added ceramic was Q„ x f= 141,800 GHz . The best
microwave quality factor was observed for ZnO -B203-SiO2 (ZBS) glass-added ceramics which can act as a perfect liquid-phase
medium for the sintering of BMT. The microwave dielectric properties of 0.2wt% ZBS-added BMT dielectric was
Q„ x f= 152,800 GHz, F,= 25.5, and Tr = - 1.5 ppm/°C
Bijumon, P V; Sreedevi, Menon K; Sebastian,M T; Mohanan, P(Microwave and Optical Technology Letters, November 20, 2002)
[+]
[-]
Abstract:
A novel technique fitr the bat dividth enhancement of conventional
rectangular microstrip antenna is proposed in this paper. When a
high permittivity dielectric resonator of suitable resonant frequency was
loaded over the patch. the % bandwidth of the antenna was increased by
more than five tunes without much affecting its gain and radiation performance.
A much more improved bandwidth was obtained when the dielectric
resonator was placed on the feedline. Experimental study shows a 2:1
VSWR bandwidth of more than 10% and excellent cross polarization performance
with increased pass band and radiation coverage abnost the same
as that of rectangular microstrip antenna
Lo, H Y; Leung, K W(Microwave and Optical Technology Letters, June 5, 2001)
[+]
[-]
Abstract:
A new configuration that employs a conducting conformal
strip to excite the low-profile equilaterial-triangular dielectric resonator
antenna (DRA) of very high permittivity is proposed. As compared with
the previous aperture-coupling configuration, the new configuration has
a wider impedance bandwidth (- 5.5%) and a higher front-to-back
radiation ratio. The return loss, radiation patterns, and antenna gain are
measured and discussed
Hunagund,P V; Jose,K A; Mohanan, P; Nair, K G(Indian Journal of Radio & Space Physics, February , 1992)
[+]
[-]
Abstract:
Results of exhaustive study of the effect of metallic flanges on H-plane radiation characteristics of V-slot
waveguide antenna are presented . It has been established that the beam can be sharpened or broadened by
varying the flange angle . The adjustment of the flange angle and flange width would further improve the
radiation pattern , yielding optimum efficiency from the flanged system
A new group of compounds with composition (Ba5-xSrx) Nb4015, having high
permittivity and low loss have been prepared and characterized in the microwave
frequency region . X-ray diffraction studies showed that monophase compound
existed for all values of x from 0 to 5. Microwave dielectric properties such as
and c f showed smooth variation with x , while the unloaded quality factor (Qu)
showed remarkable improvement with x
Saou, Wen Su; Kin, Lu Wong(Microwave and Optical Technology Letters, September 20, 2005)
[+]
[-]
Abstract:
novel design of at internal PIFA integrated with an
RF-shielding metal case for application in a clamshell or fielder-tvpe
mobile phone is presented. The integrated PIFA has a bent and tapered
radiating arm in order to easily fit in the casing of the clamshell mobile
phone as an internal antenna. The integrated PlEA can also provide a
wide operating bandwidth fir UM7S (1920-2170 MHz) operation. In
addition, for the clamshell mobile phone in either the talk or standby
condition, only a small effect on the operating bandwidth of the integrated
PIFA is obtained. The experimental results of the proposed design are presented
Haddud,T A; Al-Mansoori,M H; Zamzuri,A K; Shaharudin,S; Abdullah,M K; Mahdi,M A(Microwave and Optical Technology Letters, April 20, 2005)
[+]
[-]
Abstract:
In this paper, the generation of a multiwavelength laser
source from a Brillouin -Erbium fiber laser in the long wavelength band
(L-band) region is experimentally demonstrated. The proposed laser
system utilizes a Fabrv-Perot cavity formed by fiber-loop mirrors.
Twenty-four lines of Brillouin-Stokes with line spacings of 10 GHz are
obtained in the L-band region
Sreedevi, Menon K; Lethakumary,B; Bijumon, P V; Sebastian,M T; Mohanan, P(Microwave and Optical Technology Letters, May 5, 2005)
[+]
[-]
Abstract:
In this paper, the advantages of using L-shaped microviij)
feed to e.tcite a rectangular dielectric resonator cuuenna (DRA) by elemanagnetic
coupling are presented. This feeding technique enhances the
hardsvidth and gain of the antenna without affecting its size. The experimental
re srdts are validated using Fidelity software based on the finitedifference
tine-domain (FDTD) method
Mridula, S; Jacob,George; Mohanan, P(Microwave and Optical Technology Letters, December 20, 1999)
[+]
[-]
Abstract:
A novel antenna configuration comprised of two circular
micro strip antennas (CMAs) resonating in the TMtt and TM2, modes,
producing radiation characteristics suitable for a mobile telephone handset,
is presented. The antennas operating at the same frequency are
placed back to back with a separation comparable to the thickness of a
typical handset. The radiation pattern consists of a region of reduced
radiation intensity, which minimizes the radiation hazards to the user
Zhongyou,Yan(Microwave Engineering Group,Department of Electronics, January 5, 2002)
[+]
[-]
Abstract:
patch resonator with a via connecting ground plane is
proposed and studied experimentally. The resonant frequency of this
patch resonator is tunable up to about 34 % by adjusting the via position
in the center line. The lowest resonant frequency of this patch resonator
has been reduced by more than 64% of the same size patch resonator
A microwave dielectric ceramic resonator based on BaCe2Ti5O15 and Ba5Nb4O15 have been prepared by conventional solid state ceramic route. The dielectric resonators (DRs) have high dielectric constant 32 and 40 for BaCe2Ti5O15 and Ba5Nb4O15, respectively. The whispering gallery mode (WGM) technique was employed for the accurate determination of the dielectric properties in the microwave frequency range. The BaCe2Ti5O15 and Ba5Nb4O15 have quality factors (Q X F) of 30,600 and 53,000 respectively. The quality factor is found to depend on the azimuthal mode numbers. The temperature coefficient of resonant frequency (Tr) of BaCe2Ti5O15 and Ba5Nb4O15 have been measured accurately using different
resonant modes and are + 41 and + 78 ppm/K, respectively
The microwave dielectric properties of (I -x)CaTiO3-xSm(Mg1/2Tit,2)O3(0.1 <-x< 1.0) have been investigated. The
system forms a solid solution throughout the entire compositional range. The dielectric constant decreases from 86 to 25 as x
varies from 0.1 to 1.0. The Qxf varies non-linearly and increases for composition with x> 0.6. The nonmonotonic variation
with composition x is more pronounced in Tt than in er. The microwave dielectric properties indicate the possibility of a phase
transformation for x between 0.4 and 0.5
microwave dielectric properties of ceramics based on Ba(Mgv3Ta(2-2x)t3W,t3Tixt3)O3 is investigated as a function of x. The
15 densification as well as dielectric properties deteriorate with increase in the substitution levels of (Ti 1,3W113)333 + at (Ta213)3.33+ site
16 in Ba(Mg113Ta213)03. The rt is approaching zero between x = 0.1 and 0.15 in Ba(Mg it3Ta(2-2,,.)t3W,it3Ti,Tt3)O3 where quality factor is
17 reasonably good (Qu x f = 80,000-90,000 GHz). The Ba(Mg1,3Ta(2_,013W,13Ti,,13)03 with x = 1.0 has e, = 15.4, rf= -25.1 ppm/
18 "C, Q„ x f = 35,400 GHz
The BaO-2CeO2-nTiO2 ceramics with n = 3, 4 and 5 have been prepared with CeO2 as starting material . The ceramics have been
characterized using scanning electron microscopy , X-ray diffraction , Raman and X-ray photoelectron spectroscopy techniques. The
microwave dielectric properties have been measured using standard dielectric resonator techniques . BaO-2CeO2-3TiO2 (123),
BaO-2CeO2-4TiO2 ( 124) and BaO-2CeO2-5TiO2 ( 125) ceramics showed dielectric constants of 38, 27 and 32, respectively . All the
ceramics showed fairly good unloaded Q - factors . 124 and 125 compounds exhibited low tf values, while 123 showed a high rf value
Isuhak, Naseembeevi Jawahar; Narayana Iyer, Santha; Mailadil, Thomas Sebastian(Materials Reserach Society, December , 2002)
[+]
[-]
Abstract:
Single-phase polycrystalline ceramics in the MO-La2O3-Ti02 (M = Ca, Sr, Ba)
system, such as cation-deficient hexagonal perovskites CaLa4Ti4O15, SrLa4Ti4O15,
BaLa4Ti4O15, and Ca2La4Ti5O18 and the orthorhombic phases CaLa4Ti5O17 and
CaLa8Ti9O31, were prepared through the solid-state ceramic route. The phases
and structure of the ceramics were analyzed through x-ray diffraction and scanning
electron microscopy. The microwave dielectric properties of the ceramics were studied
using a network analyzer. The investigated ceramics show high Er in the range 42 to
54, high quality factors with Q x f in the range 16,222 to 50,215 GHz, and low Tf in
the range -25 to +6 ppm3/°C. These high dielectric constant materials with high Q x f
up to 50,215 GHz are suitable for applications where narrow bandwidth and extremely
low insertion loss is necessary, especially at frequencies around 1.9 GHz
Microwave dielectric ceramics based on RETiTaO6 (RE = La, Cc, Pr, Nd, Sm, Eu,
Gd, Tb, Dy, Ho, Y, Er, Yb, Al, and In) were prepared using a conventional solid-state
ceramic route. The structure and microstructure of the samples were analyzed using
x-ray diffraction and scanning electron microscopy techniques. The sintered samples
were characterized in the microwave frequency region. The ceramics based on Ce, Pr,
Nd, Sm, Eu, Gd, Tb, and Dy, which crystallize in orthorhombic aeschynite structure,
had a relatively high dielectric constant and positive T f while those based on Ho, Er,
and Yb, with orthorhombic euxenite structure, had a low dielectric constant and
negative Tf. The RETiTaO6 ceramics had a high-quality factor. The dielectric constant
and unit cell volume of the ceramics increased with an increase in ionic radius of the
rare-earth ions, but density decreased with it. The value of Tf increased with an
increase in RE ionic radii, and a change in the sign of Tf occurred when the ionic
radius was between 0.90 and 0.92 A. The results indicated that the boundary of the
aeschynite to euxenite morphotropic phase change lay between DyTiTaO6 and
HoTiTaO6. Low-loss ceramics like ErTiTaO6 (Er = 20.6, Qxf = 85,500), EuTiTaO6
(Er = 41.3, Qxf = 59,500), and YTiTaO6 (Er = 22.1, Q„xf = 51,400) are potential
candidates for dielectric resonator applications
Dielectric resonator ceramics with composition formula Ba[(D3+0.3 Bi0.2)Nb0.5]O3,where D3+=Y,Pr,Sm,Gd,Dy and Er,were prepared by the conventional ceramic preparation route
Dey,S; Aanandan,C K; Mohanan, P; K G Nair(Department of Electronics, June , 1993)
[+]
[-]
Abstract:
A circular miqrostrip antenna with a modified structure is
presented. By adjusting the feed location along the circumference
of the patch it is possible to match the antenna with a C
microstrip line of any impedance. The impedance bandwidth
and radiation characteristics are unaffected by this structural
V modification.