Abstract: | Ferrofluids belonging to the series, Ni x Fe1-x Fe2O4 and Zn x Fe1-x Fe2O4, were synthesized using cold co-precipitation. Liquid films of these ferrofluids were prepared by encapsulating the ferrofluids in between two optically smooth and ultrasonically cleaned glass plates. Magnetic field induced laser transmission through these ferrofluid films has been investigated. Magnetic field values can be calibrated in terms of output laser power in the low field region in which the variation is linear. This set up can be used as a cheap optical gaussmeter in the low field regime. Using the same set-up, the saturation magnetization of the sample used can also be calculated with a sample that is pre-characterized. Hence both magnetization of the sample, as well as applied magnetic field can be sensed and calculated with a precalibrated sample. |
URI: | http://dyuthi.cusat.ac.in/purl/2844 |
Files | Size |
---|---|
Dyuthi-P00397.pdf | (176.9Kb) |
Abstract: | A simple fiber optic concentration sensor based on the coupling of light f rom one fiber to another through a solution is discussed. The operational characteristics of the sensor are illustrated by taking the solutions of potassium permanganate and fast green dye as samples.The extrinsic type sensor described here shows linearity at lower concentrations. |
URI: | http://dyuthi.cusat.ac.in/purl/2638 |
Files | Size |
---|---|
Dyuthi-P0197.pdf | (2.490Mb) |
Abstract: | A simple, effective and inexpensive fiber optic sensor for investigating the setting characteristics of various grades of cement is described. A finite length of unsheathed multimode optical fiber laid inside the cement mix, is subjected to stress during the setting process. The microbends created on the fiber due to this stress directly influence the intensity of light propagating through the fiber. Continuous monitoring of such variations in the light output transmitted through the fiber gives a clear measure of the setting characteristics of the cement mix, thus providing a simple and elegant technique of great practical importance in the field of civil engineering. The smart fiber optic sensor described above can be incorporated into a building during the construction process itself so that continuous monitoring of the deterioration process for the entire life time of the building can be carried out. |
URI: | http://dyuthi.cusat.ac.in/purl/2417 |
Files | Size |
---|---|
Dyuthi-P0261.pdf | (246.9Kb) |
Abstract: | A novel sensing technique for the in situ monitoring of the rate of pulsed laser deposition (PLD) of metal thin films has been developed. This optical fibre based sensor works on the principle of the evanescent wave penetration of waveguide modes into the uncladded portion of a multimode fibre. The utility of this optical fibre sensor is demonstrated in the case of PLD of silver thin films obtained by a Q-switched Nd:YAG laser which is used to irradiate a silver target at the required conditions for the preparation of thin films. This paper describes the performance and characteristics of the sensor and shows how the device can be used as an effective tool for the monitoring of the deposition rate of silver thin films. The fibre optic sensor is very simple, inexpensive and highly sensitive compared with existing techniques for thin film deposition rate measurements |
URI: | http://dyuthi.cusat.ac.in/purl/1763 |
Files | Size |
---|---|
A fibre optic e ... ed laser deposition of.pdf | (78.21Kb) |
Abstract: | A novel sensing technique for the in situ monitoring of the rate of pulsed laser deposition (PLD) of metal thin films has been developed. This optical fibre based sensor works on the principle of the evanescent wave penetration of waveguide modes into the uncladded portion of a multimode fibre. The utility of this optical fibre sensor is demonstrated in the case of PLD of silver thin films obtained by a Q-switched Nd:YAG laser which is used to irradiate a silver target at the required conditions for the preparation of thin films. This paper describes the performance and characteristics of the sensor and shows how the device can be used as an effective tool for the monitoring of the deposition rate of silver thin films. The fibre optic sensor is very simple, inexpensive and highly sensitive compared with existing techniques for thin film deposition rate measurements. |
URI: | http://dyuthi.cusat.ac.in/purl/1764 |
Files | Size |
---|---|
Dyuthi-P0214.pdf | (78.21Kb) |
Abstract: | A fibre optic technique for detecting trace amounts of nitrite compounds in water is described. The off-line fibre optic sensor outlined here is based on evanescent field absorption in a test solution formed by the reaction of nitrite compounds in water with suitable chemical reagents. A short unclad portion of a plastic clad silica fibre acts as the sensing region. The experimental results clearly establish the usefulness of the present technique for detecting very low concentrations of the order of 1 ppb (parts per billion) of nitrite compounds with a large dynamic range of 1–1000 ppb. Such a high sensitivity enables the present device to be used for measuring the nitrite content in drinking water. |
URI: | http://dyuthi.cusat.ac.in/purl/1770 |
Files | Size |
---|---|
A fibre optic e ... race nitrites in water.pdf | (89.12Kb) |
Abstract: | The design and development of a fibre optic evanescent wave refractometer for the detection of trace amounts of paraffin oil and palm oil in coconut oil is presented. This sensor is based on a side-polished plastic optical fibre. At the sensing region, the cladding and a small portion of the core are removed and the fibre nicely polished. The sensing region is fabricated in such a manner that it sits perfectly within a bent mould. This bending of the sensing region enhances its sensitivity. The oil mixture of different mix ratios is introduced into the sensing region and we observed a sharp decrease in the output intensity. The observed variation in the intensity is found to be linear and the detection limit is 2% (by volume) paraffin oil/palm oil in coconut oil. The resolution of this refractometric sensor is of the order of 10−3. Since coconut oil is consumed in large volumes as edible oil in south India, this fibre optic sensor finds great relevance for the detection of adulterants such as paraffin oil or palm oil which are readily miscible in coconut oil. The advantage of this type of sensor is that it is inexpensive and easy to set up. Another attraction of the side-polished fibre is that only a very small amount of analyte is needed and its response time is only 7 s. |
URI: | http://dyuthi.cusat.ac.in/purl/1778 |
Files | Size |
---|---|
Fibre optic sensor for the detection of.pdf | (87.10Kb) |
Abstract: | Time resolved optical emission spectroscopy is employed to study the expansion dynamics of C2 species in a graphite plasma produced during the Nd : YAG ablation. At low laser fluences a single peak distribution with low kinetic energy is observed. At higher fluences a twin peak distribution is found. It has been noted that these double peak time of flight distribution splits into a triple peak structure at distances >_ 17mm from the target surface. The reason for the occurrence of multiple peak is due to different formation mechanisms of C2 species |
URI: | http://dyuthi.cusat.ac.in/purl/2454 |
Files | Size |
---|---|
Dyuthi-P0315.pdf | (377.4Kb) |
Abstract: | Fine particles of cobalt ferrite were synthesized by the sol–gel method. Subsequent heat treatment at different temperatures yielded cobalt ferrites having different grain sizes. X-ray diffraction studies were carried out to elucidate the structure of all the samples. Dielectric permittivity and ac conductivity of all the samples were evaluated as a function of frequency, temperature and grain size. The variation of permittivity and ac conductivity with frequency reveals that the dispersion is due to Maxwell–Wagner type interfacial polarization in general, with a noted variation from the expected behaviour for the cold synthesized samples. High permittivity and conductivity for small grains were explained on the basis of the correlated barrier-hopping model |
Description: | J. Phys. D: Appl. Phys. 40 (2007) 1593–1602 |
URI: | http://dyuthi.cusat.ac.in/purl/4350 |
Files | Size |
---|---|
Finite size eff ... e polarization effects.pdf | (975.7Kb) |
Abstract: | Nanoparticles of nickel ferrite have been synthesized by the sol–gel method and the effect of grain size on its structural and magnetic properties have been studied in detail. X-ray diffraction (XRD) studies revealed that all the samples are single phasic possessing the inverse spinel structure. Grain size of the sol–gel synthesized powders has been determined from the XRD data and the strain graph. A grain size of 9 nm was observed for the as prepared powders of NiFe2O4 obtained through the sol–gel method. It was also observed that strain was induced during the firing process. Magnetization measurements have been carried out on all the samples prepared in the present series. It was found that the specific magnetization of the nanosized NiFe2O4 powders was lower than that of the corresponding coarse-grained counterparts and decreased with a decrease in grain size. The coercivity of the sol–gel synthesized NiFe2O4 nanoparticles attained a maximum value when the grain size was 15nm and then decreased as the grain size was increased further. |
Description: | Journal of Magnetism and Magnetic Materials 302 (2006) 190–195 |
URI: | http://dyuthi.cusat.ac.in/purl/4347 |
Files | Size |
---|---|
Finite size eff ... esized NiFe2O4 powders.pdf | (265.1Kb) |
Abstract: | The whale shark (Rhiniodon typus Smith) is an under exploited species and it is mainly caught for its liver oil . The processing of shark fin for rays is reported here . The fins have a high content of rays . The yield of fin rays from undried fins ranged from 0 .53 to 4 .40 percent with maximum ray content in the lower lobe of caudal fin . The physical and chemical characteristics of the rays are reported . The total nitrogen content is about 15 to 16 percent (dry weight basis) |
Description: | FISHERY TECHNOLOGY,Vol. 27, 1990 |
URI: | http://dyuthi.cusat.ac.in/purl/4117 |
Files | Size |
---|---|
Fins and Fin Ra ... Rhiniodon typus Smith).pdf | (258.6Kb) |
Abstract: | This paper describes the first use of polystyrene-supported poly(amidoamine) (PAMAM) dendrimers as heterogeneous basic organocatalysts for carbon–carbon bond formation. Polystyrene-supported PAMAM dendrimers of first, second and third generations have been used as reusable base catalysts in Knoevenagel condensations of carbonyl compounds with active methylene compounds. The reactions proceed in short periods of time and with 100% selectivity. This novel catalyst eliminates the use of aromatic and halogenated solvents, as well as complex purification processes. The catalysts can be recycled ten times. |
URI: | http://dyuthi.cusat.ac.in/xmlui/purl/1966 |
Files | Size |
---|---|
First Exaple of Organocatalysis....pdf | (135.4Kb) |
Abstract: | The article examines the commodity chain trap of marine fishery in Kerala, at both material and value terms, and its ramifications in the globalised fishery chains. The marketing chains both material and value, are very complex in nature since they involve many types of markets and large number of intermediaries and participants. The article also scrutinizes the sensitivity of consumers’ and country’s responses in terms of dietary and hygienic standards relating to seafood trade. In addition, it discusses the devastating effect about the recent stipulations like the US Bio- Terrorism Act and Shrimp anti-dumping duty on the Kerala fishery products |
Description: | Developing Country Studies,Vol 2, No.5, 2012 |
URI: | http://dyuthi.cusat.ac.in/purl/4592 |
Files | Size |
---|---|
Fishery Commodi ... Kerala Marine Fishery.pdf | (626.6Kb) |
Abstract: | The spoilage characteristics of bacterial strains were studied by growing them at 28 _+ 2 °C in agar and broth media prepared with sterile fish and prawn flesh homogenates. The percentage of spoilers found among the bacterial isolates tested, as shown by odour production and halo zone formation, was independent of the source of flesh used. Indole and fluorescent pigment production were also observed in the broth. Pseudomonas, Vibrio and Acinetobacter exhibited faster growth in flesh media than in the usual artificial media. Decrease of protein and lipid concentration in the clear zone of agar media suggests the utilization of the available substrate by spoilage bacteria. |
Description: | Antonie van Leeuwenhoek 51 (1985) 219-225 |
URI: | http://dyuthi.cusat.ac.in/purl/4261 |
Files | Size |
---|---|
Fish flesh agar ... n of spoilage bacteria.pdf | (743.0Kb) |
Abstract: | Result of the study on traditional traps in the inland waters of three northern districts viz, Kasargod, Kannur and Kozhikode in Kerala state during 2003-2004 is presented. Mainly six types of traps are found in operation. Chempally koode is a rectangular bamboo trap with" D" shape in cross section operated without bait in some rivers of Kannur and Kasargod. Bamboo screen barriers are almost completely replaced with durable HDPE net screen to make handling easy. Thottil vala is a unique aerial trap operated from the dam in Pazhassi reservoir during monsoon to catch big fishes jumping against flowing water. |
Description: | fishery technology,2008 vol 45(2)pp 137-146 |
URI: | http://dyuthi.cusat.ac.in/purl/4131 |
Files | Size |
---|---|
Fish traps in inland waters of north kerala.pdf | (720.4Kb) |
Abstract: | Invertase was immobilized on acid activated montmorillonite via two independent procedures, adsorption and covalent binding. The immobilized enzymes were characterized by XRD, NMR and N2 adsorption measurements and their activity was tested in a fixed bed reactor. XRD revealed that the enzyme was situated on the periphery of the clay and the side chains of different amino acid residues were involved in intercalation with the clay matrix. NMR demonstrated that tetrahedral Al was linked to the enzyme during adsorption and the octahedral Al was involved during covalent binding. Secondary interaction of the enzyme with Al was also observed. N2 adsorption studies showed that covalent binding of enzymes caused pore blockage since the highly polymeric species were located at the pore entrance. The fixed bed reactor proved to be efficient for the immobilized invertase. The optimum pH and pH stability improved upon immobilization. The kinetic parameters calculated also showed an enhanced efficiency of the immobilized systems. They could be used continuously for long period. Covalently bound invertase demonstrated greater operational stability. |
URI: | http://dyuthi.cusat.ac.in/purl/2270 |
Files | Size |
---|---|
Dyuthi-SS60.pdf | (481.4Kb) |
Abstract: | Decimal multiplication is an integral part of financial, commercial, and internet-based computations. A novel design for single digit decimal multiplication that reduces the critical path delay and area for an iterative multiplier is proposed in this research. The partial products are generated using single digit multipliers, and are accumulated based on a novel RPS algorithm. This design uses n single digit multipliers for an n × n multiplication. The latency for the multiplication of two n-digit Binary Coded Decimal (BCD) operands is (n + 1) cycles and a new multiplication can begin every n cycle. The accumulation of final partial products and the first iteration of partial product generation for next set of inputs are done simultaneously. This iterative decimal multiplier offers low latency and high throughput, and can be extended for decimal floating-point multiplication. |
Description: | Parallel and Distributed Processing with Applications, 2008. ISPA'08. International Symposium on |
URI: | http://dyuthi.cusat.ac.in/purl/3874 |
Files | Size |
---|---|
Fixed Point Dec ... on using RPS Algorithm.pdf | (424.3Kb) |
Abstract: | Flexile single layer electromagnetic wave absorbers were designed by incorporating appropriate amounts of carbon black in a nitrile butadiene rubber matrix along with an optimized amount of magnetic counterpart, namely, barium hexaferrite for applications in S, C, and X-bands. Effective dielectric permittivity and magnetic permeability were measured using cavity perturbation method in the frequency range of 2–12 GHz. The microwave absorbing characteristics of the composites were studied in the S, C, and X-bands employing a model in which an electromagnetic wave is incident normally on a metal terminated single layer. Reflection loss exceeding 20 dB is obtained for all the samples in a wide frequency range of 2–12 GHz when an appropriate absorber thickness between 5 and 9mm is chosen. The impact of carbon black is clearly observed in the optimized composites on the mechanical strength, thickness, band width of absorption, dielectric properties, |
Description: | J. Appl. Phys. 116, 024902 (2014) |
URI: | http://dyuthi.cusat.ac.in/purl/4426 |
Files | Size |
---|---|
Flexible microw ... 2–12 GHz applications.pdf | (2.341Mb) |
Abstract: | This paper gives the details of flexure-shear analysis of concrete beams reinforced with GFRP rebars. The influence of vertical reinforcement ratio, longitudinal reinforcement ratio and compressive strength of concrete on shear strength of GFRP reinforced concrete beam is studied. The critical value of shear span to depth ratio (a/d) at which the mode of failure changes from flexure to shear is studied. The fail-ure load of the beam is predicted for various values of a/d ratio. The prediction show that the longitudinally FRP reinforced concrete beams having no stirrups fail in shear for a/d ratio less than 9.0. It is expected that the predicted data is useful for structural engineers to design the FRP reinforced concrete members. |
Description: | CICE 2010 - The 5th International Conference on FRP Composites in Civil EngineeringSeptember 27-29, 2010 Beijing, China |
URI: | http://dyuthi.cusat.ac.in/purl/4541 |
Files | Size |
---|---|
Flexure-shear A ... nforced with GFRP bars.pdf | (152.1Kb) |
Abstract: | Preparation of an appropriate optical-fiber preform is vital for the fabrication of graded-index polymer optical fibers (GIPOF), which are considered to be a good choice for providing inexpensive high bandwidth data links, for local area networks and telecommunication applications. Recent development of the interfacial gel polymerization technique has caused a dramatic reduction in the total attenuation in GIPOF, and this is one of the potential methods to prepare fiber preforms for the fabrication of dye-doped polymer-fiber amplifiers. In this paper, the preparation of a dye-doped graded-index poly(methyl methacrylate) (PMMA) rod by the interfacial gel polymerization method using a PMMA tube is reported. An organic compound of high-refractive index, viz., diphenyl phthalate (DPP), was used to obtain a graded-index distribution, and Rhodamine B (Rh B), was used to dope the PMMA rod. The refractive index profile of the rod was measured using an interferometric technique and the index exponent was estimated. The single pass gain of the rod was measured at a pump wavelength of 532 nm. The extent of doping of the Rh B in the preform was studied by axially exciting a thin slice of the rod with white light and measuring the spatial variation of the fluorescence intensity across the sample. |
URI: | http://dyuthi.cusat.ac.in/purl/2582 |
Files | Size |
---|---|
Dyuthi-P0142.pdf | (695.6Kb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.