Abstract: | The effect of frequency, composition and temperature on the a.c. electrical conductivity were studied for the ceramic, Ni1–xZnxFe2O4, as well as the filler (Ni1–xZnxFe2O4) incorporated rubber ferrite composites (RFCs). Ni1–xZnxFe2O4 (where x varies from 0 to 1 in steps of 0×2) were prepared by usual ceramic techniques. They were then incorporated into a butyl rubber matrix according to a specific recipe. The a.c. electrical conductivity (sa.c.) calculations were carried out by using the data available from dielectric measurements and by employing a simple relationship. The a.c. conductivity values were found to be of the order of 10–3 S/m. Analysis of the results shows that sa.c. increases with increase of frequency and the change is same for both ceramic Ni1–xZnxFe2O4 and RFCs. sa.c. increases initially with the increase of zinc content and then decreases with increase of zinc. Same behaviour is observed for RFCs too. The dependence of sa.c. on the volume fraction of the magnetic filler was also studied and it was found that the a.c. conductivity of RFCs increases with increase of volume fraction of the magnetic filler. Temperature dependence of conductivity was studied for both ceramic and rubber ferrite composites. Conductivity shows a linear dependence with temperature in the case of ceramic samples |
Description: | Bull. Mater. Sci., Vol. 25, No. 7, December 2002, pp. 599–607 |
URI: | http://dyuthi.cusat.ac.in/purl/4355 |
Files | Size |
---|---|
Evaluation of a ... ielectric measurements.pdf | (232.7Kb) |
Abstract: | In this paper the effectiveness of a novel method of computer assisted pedicle screw insertion was studied using testing of hypothesis procedure with a sample size of 48. Pattern recognition based on geometric features of markers on the drill has been performed on real time optical video obtained from orthogonally placed CCD cameras. The study reveals the exactness of the calculated position of the drill using navigation based on CT image of the vertebra and real time optical video of the drill. The significance value is 0.424 at 95% confidence level which indicates good precision with a standard mean error of only 0.00724. The virtual vision method is less hazardous to both patient and the surgeon |
Description: | International Journal of Scientific and Research Publications, Volume 4, Issue 2, February 2014 |
URI: | http://dyuthi.cusat.ac.in/purl/4577 |
Files | Size |
---|---|
Evaluation Of A Novel Method Of........pdf | (516.8Kb) |
Abstract: | The electrical conductivity and thermal diffusivity of pristine and iodine doped vanadyl naphthalocyanine (VONc) were studied. In the pristine sample, the temperature dependence was very weak below 300 K. The increase in conductivity at higher temperature must be due to an enhancement in carrier density with increase in thermal energy. The electrical conductivity of VONc increased when doped with iodine. The behavior of VONcI indicated that considerable changes have occurred in the electronic environment of the molecule as a result of doping. Iodine doping enhanced the thermal diffusivity of VONc. The increase in thermal diffusivity of the iodine doped sample may be due to the disorder of iodine atoms occupying the channels in one dimensional lattices. |
URI: | http://dyuthi.cusat.ac.in/purl/2387 |
Files | Size |
---|---|
Dyuthi-P0210.pdf | (49.04Kb) |
Abstract: | The acoustic signals generated in solids due to interaction with pulsed laser beam is used to determine the ablation threshold of bulk polymer samples of teflon (polytetrafluoroethylene) and nylon under the irradiation from a Q-switched Nd:YAG laser at 1.06µm wavelength. A suitably designed piezoelectric transducer is employed for the detection of photoacoustic (PA) signals generated in this process. It has been observed that an abrupt increase in the amplitude of the PA signal occurs at the ablation threshold. Also there exist distinct values for the threshold corresponding to different mechanisms operative in producing damages like surface morphology, bond breaking and melting processes at different laser energy densities. |
URI: | http://dyuthi.cusat.ac.in/purl/2501 |
Files | Size |
---|---|
Dyuthi-P0292.pdf | (706.9Kb) |
Abstract: | Random genetic changes generated during in vitro culture are not desirable for plant micropropagation and genetic transformation. RAPD markers were used to detect the variation in leaf disc callus cultures of Jatropha curcas, maintained in Murashige and Skoog (MS) medium with different auxin and cytokinin combinations. In total 41 scorable bands were produced with 11 primers. Out of 41 bands, 37 were polymorphic (91.12%). The average number of polymorphic bands was 3.36 per primer. The highest similarity (0.82) with mother plant was seen in callus maintained on MS with hormonal combination Indole butyric acid - 0.4mg/l+ N6-benzyladenine purine - 4.0 mg/l. The callus grown on MS with hormonal combinations IBA- 0.4mg/l+ BAP- 2.0mg/l, IBA- 0.4mg/l+ BAP- 2.5mg/l and IBA- 0.6 mg/l+ BAP- 2.0 mg/l also showed similarity with the mother plant. Callus maintained on MS with hormonal combination IBA- 0.2mg/l+ BAP- 2.0 mg/l was found to show least similarity (0.53) with mother plant |
Description: | World Journal of Agricultural Sciences 8 (6): 616-623, 2012 |
URI: | http://dyuthi.cusat.ac.in/purl/4734 |
Files | Size |
---|---|
Evaluation of S ... ons Using RAPD Markers.pdf | (419.8Kb) |
Abstract: | Sensor networks are one of the fastest growing areas in broadwireless ad hoc networking (?Eld. A sensor node, typically'contains signal-processing circuits, micro-controllers and awireless transmitter/receiver antenna. Energy saving is oneof the critical issue for sensor networks since most sensorsare equipped with non-rechargeable batteries that have limited lifetime.In thiswork, four routing protocols for wireless sensor networks vizFlooding, Gossiping, GBR and LEACH have been simulated using Tiny OS and their power consumption is studied usingcaorwreiredTOoSuStIuMs.ingAMirceaal2izMaotitoens.of these protocols has been carried out using mica 2 motes |
URI: | http://dyuthi.cusat.ac.in/purl/4178 |
Files | Size |
---|---|
Evaluation of t ... reless Sensor Networks.pdf | (906.9Kb) |
Abstract: | Sensor networks are one of the fastest growing areas in broad of a packet is in transit at any one time. In GBR, each node in the network can look at itsneighbors wireless ad hoc networking (? Eld. A sensor node, typically'hop count (depth) and use this to decide which node to forward contains signal-processing circuits, micro-controllers and a the packet on to. If the nodes' power level drops below a wireless transmitter/receiver antenna. Energy saving is one certain level it will increase the depth to discourage trafiE of the critical issue for sensor networks since most sensors are equipped with non-rechargeable batteries that have limitedlifetime. Routing schemes are used to transfer data collectedby sensor nodes to base stations. In the literature many routing protocols for wireless sensor networks are suggested. In this work, four routing protocols for wireless sensor networks viz Flooding, Gossiping, GBR and LEACH have been simulated using TinyOS and their power consumption is studied using PowerTOSSIM. A realization of these protocols has beencarried out using Mica2 Motes. |
Description: | Ad Hoc and Ubiquitous Computing, 2006. ISAUHC'06. International Symposium on |
URI: | http://dyuthi.cusat.ac.in/purl/3882 |
Files | Size |
---|---|
Evaluation of t ... reless Sensor Networks.pdf | (906.1Kb) |
Abstract: | Sensor networks are one of the fastest growing areas in broad of a packet is in transit at any one time. In GBR, each node in the network can look at itsneighbors wireless ad hoc networking (? Eld. A sensor node, typically'hop count (depth) and use this to decide which node to forward contains signal-processing circuits, micro-controllers and a the packet on to. If the nodes' power level drops below a wireless transmitter/receiver antenna. Energy saving is one certain level it will increase the depth to discourage trafiE of the critical issue forfor sensor networks since most sensors are equipped with non-rechargeable batteries that have limited lifetime. |
Description: | Ad Hoc and Ubiquitous Computing, 2006. ISAUHC'06. International Symposium on |
URI: | http://dyuthi.cusat.ac.in/purl/4145 |
Files | Size |
---|---|
Evaluation of the Power Consumption of.pdf | (906.1Kb) |
Abstract: | Thermodynamic parameters of the atmosphere form part of the input to numerical forecasting models. Usually these parameters are evaluated from a thermodynamic diagram. Here, a technique is developed to evaluate these parameters quickly and accurately using a Fortran program. This technique is tested with four sets of randomly selected data and the results are in agreement with the results from the conventional method. This technique is superior to the conventional method in three respects: more accuracy, less computation time, and evaluation of additional parameters. The computation time for all the parameters on a PC AT 286 machine is II sec. This software, with appropriate modifications, can be used, for verifying various lines on a thermodynamic diagram |
Description: | Computers & Geosciences Vol. 22, No.8, pp. 877-88 1, 1996 |
URI: | http://dyuthi.cusat.ac.in/purl/3784 |
Files | Size |
---|---|
CAB_.C.G.pdf | (5.099Mb) |
Abstract: | In this communication, we discuss the details of fabricating an off-line fibre optic sensor (FOS) based on evanescent wave absorption for detecting trace amounts of Fe3+ in water. Two types of FOS are developed; one type uses the unclad portion of a multimode silica fibre as the sensing region whereas the other employs the microbent portion of a multimode plastic fibre as the sensing region. Sensing is performed by measuring the absorption of the evanescent wave in a reagent medium surrounding the sensing region. To evaluate the relative merits of the two types of FOS in Fe3+ sensing, a comparative study of the sensors is made, which reveals the superiority of the latter in many respects, such as smaller sensing length, use of a double detection scheme (for detecting both core and cladding modes) and higher sensitivity of cladding mode detection at an intermediate range of concentration along with the added advantage that plastic fibres are inexpensive. A detection limit of 1 ppb is observed in both types of fibre and the range of detection can be as large as 1 ppb–50 ppm. All the measurements are carried out using a LabVIEW set-up. |
URI: | http://dyuthi.cusat.ac.in/purl/738 |
Files | Size |
---|---|
e30622.pdf | (176.4Kb) |
Abstract: | In this communication, we discuss the details of fabricating an off-line fibre optic sensor (FOS) based on evanescent wave absorption for detecting trace amounts of Fe3+ in water. Two types of FOS are developed; one type uses the unclad portion of a multimode silica fibre as the sensing region whereas the other employs the microbent portion of a multimode plastic fibre as the sensing region. Sensing is performed by measuring the absorption of the evanescent wave in a reagent medium surrounding the sensing region. To evaluate the relative merits of the two types of FOS in Fe3+ sensing, a comparative study of the sensors is made, which reveals the superiority of the latter in many respects, such as smaller sensing length, use of a double detection scheme (for detecting both core and cladding modes) and higher sensitivity of cladding mode detection at an intermediate range of concentration along with the added advantage that plastic fibres are inexpensive. A detection limit of 1 ppb is observed in both types of fibre and the range of detection can be as large as 1 ppb–50 ppm. All the measurements are carried out using a LabVIEW set-up. |
URI: | http://dyuthi.cusat.ac.in/purl/737 |
Files | Size |
---|---|
e30622.pdf | (176.4Kb) |
Abstract: | In this communication, we discuss the details of fabricating an off-line fibre optic sensor (FOS) based on evanescent wave absorption for detecting trace amounts of Fe3+ in water. Two types of FOS are developed; one type uses the unclad portion of a multimode silica fibre as the sensing region whereas the other employs the microbent portion of a multimode plastic fibre as the sensing region. Sensing is performed by measuring the absorption of the evanescent wave in a reagent medium surrounding the sensing region. To evaluate the relative merits of the two types of FOS in Fe3+ sensing, a comparative study of the sensors is made, which reveals the superiority of the latter in many respects, such as smaller sensing length, use of a double detection scheme (for detecting both core and cladding modes) and higher sensitivity of cladding mode detection at an intermediate range of concentration along with the added advantage that plastic fibres are inexpensive. A detection limit of 1 ppb is observed in both types of fibre and the range of detection can be as large as 1 ppb–50 ppm. All the measurements are carried out using a LabVIEW set-up. |
URI: | http://dyuthi.cusat.ac.in/purl/602 |
Files | Size |
---|---|
Dyuthi-P0251.pdf | (176.4Kb) |
Abstract: | In this communication, we discuss the details of fabricating an off-line fibre optic sensor (FOS) based on evanescent wave absorption for detecting trace amounts of Fe3+ in water. Two types of FOS are developed; one type uses the unclad portion of a multimode silica fibre as the sensing region whereas the other employs the microbent portion of a multimode plastic fibre as the sensing region. Sensing is performed by measuring the absorption of the evanescent wave in a reagent medium surrounding the sensing region. To evaluate the relative merits of the two types of FOS in Fe3+ sensing, a comparative study of the sensors is made, which reveals the superiority of the latter in many respects, such as smaller sensing length, use of a double detection scheme (for detecting both core and cladding modes) and higher sensitivity of cladding mode detection at an intermediate range of concentration along with the added advantage that plastic fibres are inexpensive. A detection limit of 1 ppb is observed in both types of fibre and the range of detection can be as large as 1 ppb–50 ppm. All the measurements are carried out using a LabVIEW set-up. |
URI: | http://dyuthi.cusat.ac.in/purl/603 |
Files | Size |
---|---|
e30622.pdf | (176.4Kb) |
Abstract: | The design and development of an evanescent wave sensor to determine the etching rate of the core of an optical fibre is discussed in this paper. The working of the device is based on the principle of propagation and loss of the evanescent wave in the cladding region of the fibre. The fraction of light intensity creeping out of the core of an uncladded fibre is a function of the core radius. As this radius decreases, the evanescent wave coupling to the medium surrounding the core enhances. This results in a decrease of the transmitted light intensity through the fibre. This technique is useful to design and fabricate optical fibres with different core geometries. |
URI: | http://dyuthi.cusat.ac.in/purl/2640 |
Files | Size |
---|---|
Dyuthi-P0327.pdf | (226.6Kb) |
Abstract: | Superparamagnetic nanocomposites based on Y-Fe2O3 and sulphonated polystyrene were synthesised by ion-exchange process and the structural characterisation has been carried out using X-ray diffraction technique. Doping of cobalt in to the Y-Fe2O3 lattice was effected in situ and the doping was varied in the atomic percentage range 1–10. The optical absorption studies show a band gap of 2.84 eV, which is blue shifted by 0.64 eV when compared to the reported values for the bulk samples (2.2 eV). This is explained on the basis of weak quantum confinement. Further size reduction can result in a strong confinement, which can yield transparent magnetic nanocomposites because of further blue shifting. The band gap gets red shifted further with the addition of cobalt in the lattice and this red shift increases with the increase in doping. The observed red shift can be attributed to the strain in the lattice caused by the anisotropy induced by the addition of cobalt. Thus, tuning of bandgap and blue shifting is aided by weak exciton confinement and further red shifting of the bandgap is assisted by cobalt doping. |
URI: | http://dyuthi.cusat.ac.in/purl/2836 |
Files | Size |
---|---|
Dyuthi-P00392.pdf | (199.0Kb) |
Abstract: | Nanoparticles are of immense importance both from the fundamental and application points of view. They exhibit quantum size effects which are manifested in their improved magnetic and electric properties. Mechanical attrition by high energy ball milling (HEBM) is a top down process for producing fine particles. However, fineness is associated with high surface area and hence is prone to oxidation which has a detrimental effect on the useful properties of these materials. Passivation of nanoparticles is known to inhibit surface oxidation. At the same time, coating polymer film on inorganic materials modifies the surface properties drastically. In this work a modified set-up consisting of an RF plasma polymerization technique is employed to coat a thin layer of a polymer film on Fe nanoparticles produced by HEBM. Ball-milled particles having different particle size ranges are coated with polyaniline. Their electrical properties are investigated by measuring the dc conductivity in the temperature range 10–300 K. The low temperature dc conductivity (I–V ) exhibited nonlinearity. This nonlinearity observed is explained on the basis of the critical path model. There is clear-cut evidence for the occurrence of intergranular tunnelling. The results are presented here in this paper |
Description: | Nanotechnology 17 (2006) 4765–4772 |
URI: | http://dyuthi.cusat.ac.in/purl/4381 |
Files | Size |
---|---|
Evidence for in ... ted α-Fe nanoparticles.pdf | (762.3Kb) |
Abstract: | Nanoparticles of manganese ferrite were prepared by the chemical co-precipitation technique. The dielectric parameters, namely, real and imaginary dielectric permittivity (ε and ε ), ac conductivity (σac) and dielectric loss tangent (tan δ), were measured in the frequency range of 100 kHz–8MHz at different temperatures. The variations of dielectric dispersion (ε ) and dielectric absorption (ε ) with frequency and temperature were also investigated. The variation of dielectric permittivity with frequency and temperature followed the Maxwell–Wagner model based on interfacial polarization in consonance with Koops phenomenological theory. The dielectric loss tangent and hence ε exhibited a relaxation at certain frequencies and at relatively higher temperatures. The dispersion of dielectric permittivity and broadening of the dielectric absorption suggest the possibility of a distribution of relaxation time and the existence of multiple equilibrium states in manganese ferrite. The activation energy estimated from the dielectric relaxation is found to be high and is characteristic of polaron conduction in the nanosized manganese ferrite. The ac conductivity followed a power law dependence σac = Bωn typical of charge transport assisted by a hopping or tunnelling process. The observed minimum in the temperature dependence of the frequency exponent n strongly suggests that tunnelling of the large polarons is the dominant transport process |
Description: | J. Phys. D: Appl. Phys. 41 (2008) 185005 (9pp) |
URI: | http://dyuthi.cusat.ac.in/purl/4354 |
Files | Size |
---|---|
Evidence for po ... ured manganese ferrite.pdf | (2.000Mb) |
Abstract: | In any investigation, information about the molecules under consideration is very essential for tailoring their properties. Evaluation of dispersion parameters, namely optical dielectric constant, static dielectric constant, relaxation time and spreading factor, assumes significance in this context. Dielectric spectroscopy is a useful tool for estimating these parameters. Not only does it reveal details about these constants but it also gives insight into the mechanism of conduction. In this paper the evaluation of dispersion parameters of cobalt phthalocyanine tetramer in the temperature range 300–393K is attempted using Cole–Cole plots. The temperature variation of the spreading factor indicates the existence of multiple equilibrium positions in the case of cobalt phthalocyanine tetramer. To the best of our knowledge, the evaluation of dispersion parameters for cobalt phthalocyanine tetramer is reported for the first time |
Description: | J. Phys. D: Appl. Phys. 39 (2006) 1678–1683 |
URI: | http://dyuthi.cusat.ac.in/purl/4409 |
Files | Size |
---|---|
Evidence for th ... ielectric spectroscopy.pdf | (274.5Kb) |
Abstract: | We analyse numerically the bifurcation structure of a two-dimensional noninvertible map and show that different periodic cycles are arranged in it exactly in the same order as in the case of the logistic map. We also show that this map satisfies the general criteria for the existence of Sarkovskii ordering, which supports our numerical result. Incidently, this is the first report of the existence of Sarkovskii ordering in a two-dimensional map. |
URI: | http://dyuthi.cusat.ac.in/purl/2569 |
Files | Size |
---|---|
Dyuthi-P0128.pdf | (408.6Kb) |
Abstract: | Whitespot virus could be experimentally transmitted from infected Penoeus monodon to P. in.dicus and repeatedly passed on through several batches of apparently healthy J'. in dieas. During these passages, white spots first disappeared before subsequently reappearing, Electron microscopic studies revealed the presence of oblong-shaped, fully-assembled virus towards the periphery and virus in paracrystalline arrnys towards the center of the hypertrophied nuclei. The virus isolated here is referred to as whitespot syndrome baculovirus (WSBV) until more is known of its antigenic .md genomic rclatodnc..s to isolates from other countries |
Description: | Aeiau Fisheries Science 12(1999):41-47 Asian Fisheries Society, Manila, Philippines |
URI: | http://dyuthi.cusat.ac.in/purl/4073 |
Files | Size |
---|---|
Evidence Of A B ... Milne Edwards In India.pdf | (432.8Kb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.