Abstract: | A novel sensing technique for the in situ monitoring of the rate of pulsed laser deposition (PLD) of metal thin films has been developed. This optical fibre based sensor works on the principle of the evanescent wave penetration of waveguide modes into the uncladded portion of a multimode fibre. The utility of this optical fibre sensor is demonstrated in the case of PLD of silver thin films obtained by a Q-switched Nd:YAG laser which is used to irradiate a silver target at the required conditions for the preparation of thin films. This paper describes the performance and characteristics of the sensor and shows how the device can be used as an effective tool for the monitoring of the deposition rate of silver thin films. The fibre optic sensor is very simple, inexpensive and highly sensitive compared with existing techniques for thin film deposition rate measurements. |
URI: | http://dyuthi.cusat.ac.in/purl/1764 |
Files | Size |
---|---|
Dyuthi-P0214.pdf | (78.21Kb) |
Abstract: | A fibre optic technique for detecting trace amounts of nitrite compounds in water is described. The off-line fibre optic sensor outlined here is based on evanescent field absorption in a test solution formed by the reaction of nitrite compounds in water with suitable chemical reagents. A short unclad portion of a plastic clad silica fibre acts as the sensing region. The experimental results clearly establish the usefulness of the present technique for detecting very low concentrations of the order of 1 ppb (parts per billion) of nitrite compounds with a large dynamic range of 1–1000 ppb. Such a high sensitivity enables the present device to be used for measuring the nitrite content in drinking water. |
URI: | http://dyuthi.cusat.ac.in/purl/1770 |
Files | Size |
---|---|
A fibre optic e ... race nitrites in water.pdf | (89.12Kb) |
Abstract: | The design and development of a fibre optic evanescent wave refractometer for the detection of trace amounts of paraffin oil and palm oil in coconut oil is presented. This sensor is based on a side-polished plastic optical fibre. At the sensing region, the cladding and a small portion of the core are removed and the fibre nicely polished. The sensing region is fabricated in such a manner that it sits perfectly within a bent mould. This bending of the sensing region enhances its sensitivity. The oil mixture of different mix ratios is introduced into the sensing region and we observed a sharp decrease in the output intensity. The observed variation in the intensity is found to be linear and the detection limit is 2% (by volume) paraffin oil/palm oil in coconut oil. The resolution of this refractometric sensor is of the order of 10−3. Since coconut oil is consumed in large volumes as edible oil in south India, this fibre optic sensor finds great relevance for the detection of adulterants such as paraffin oil or palm oil which are readily miscible in coconut oil. The advantage of this type of sensor is that it is inexpensive and easy to set up. Another attraction of the side-polished fibre is that only a very small amount of analyte is needed and its response time is only 7 s. |
URI: | http://dyuthi.cusat.ac.in/purl/1778 |
Files | Size |
---|---|
Fibre optic sensor for the detection of.pdf | (87.10Kb) |
Abstract: | Many finite elements used in structural analysis possess deficiencies like shear locking, incompressibility locking, poor stress predictions within the element domain, violent stress oscillation, poor convergence etc. An approach that can probably overcome many of these problems would be to consider elements in which the assumed displacement functions satisfy the equations of stress field equilibrium. In this method, the finite element will not only have nodal equilibrium of forces, but also have inner stress field equilibrium. The displacement interpolation functions inside each individual element are truncated polynomial solutions of differential equations. Such elements are likely to give better solutions than the existing elements.In this thesis, a new family of finite elements in which the assumed displacement function satisfies the differential equations of stress field equilibrium is proposed. A general procedure for constructing the displacement functions and use of these functions in the generation of elemental stiffness matrices has been developed. The approach to develop field equilibrium elements is quite general and various elements to analyse different types of structures can be formulated from corresponding stress field equilibrium equations. Using this procedure, a nine node quadrilateral element SFCNQ for plane stress analysis, a sixteen node solid element SFCSS for three dimensional stress analysis and a four node quadrilateral element SFCFP for plate bending problems have been formulated.For implementing these elements, computer programs based on modular concepts have been developed. Numerical investigations on the performance of these elements have been carried out through standard test problems for validation purpose. Comparisons involving theoretical closed form solutions as well as results obtained with existing finite elements have also been made. It is found that the new elements perform well in all the situations considered. Solutions in all the cases converge correctly to the exact values. In many cases, convergence is faster when compared with other existing finite elements. The behaviour of field consistent elements would definitely generate a great deal of interest amongst the users of the finite elements. |
Description: | Department of Ship Technology, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2121 |
Files | Size |
---|---|
Dyuthi-T0411.pdf | (1.799Mb) |
Abstract: | Important issues related to femtosecond (fs) pulses and its relevance to this thesis are discussed. A fundamental characteristic, like the timebandwidth product for fs pulses is decribed in detail. A brief review of generation of ultrashort pulses and its propagation through an optically transparent media are presented. Interaction of strong pulses with matter and different ionization processes are also described. An overview of the thesis is presented at the end |
URI: | http://dyuthi.cusat.ac.in/purl/5097 |
Files | Size |
---|---|
Dyuthi- T 2163.pdf | (11.76Mb) |
Description: | Dept.of Applied Economics,Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2783 |
Files | Size |
---|---|
Dyuthi-T0806.pdf | (2.129Mb) |
Abstract: | Financial inclusion for inclusive growth is central to the developmental philosophy of most of the nations over the past decade. It has been a priority for policy makers and regulators in financial sector development for improving access and usage of financial services to achieve comprehensive financial inclusion. The initiatives taken towards financial inclusion can promote a more effective and efficient process to achieve significant improvements in financial inclusion are to establish and achieve shared and sustainable development and growth. Realising this, an increasing number of countries are committing to promote financial inclusion, encouraged by the growing body of country level experiences (World Bank, 2012). Financial inclusion basically means, broad based growth through participation as well as sharing the benefits from the growth process along with the under privileged and marginal segments of the economy. Evidence suggests that it has substantial benefits for equitable and sustainable growth. Inclusive growth ensures that while economy grows rapidly, all segments of society are involved in this growth process, ensuring equal opportunities, devoid of any regional or sectoral disparitiesIt is widely acknowledged that the objective ofinclusive growth is accomplished through the process of financial inclusion. Financial inclusion envisages bringing everyone, irrespective of financial status, into the banking fold for the individual progress and development and thereby achieving comprehensive growth with equity |
URI: | http://dyuthi.cusat.ac.in/purl/5085 |
Files | Size |
---|---|
Dyuthi- 2151.pdf.pdf | (2.971Mb) |
Abstract: | Today India is seeking a speedy transformation of her semi-stagnant economy to a dynamic one by means of economic planning in a democratic set up. In the context of this growth oriented endeavour public sector has a vital role to play. After three decades of planned development, it has become important that India must make fresh appraisals on the role of public sector in the economic renaissance of the country. Almost no comprehensive study has been made on this vital segment of the economy vis-a-vis the growth economics. This study is an attempt to fill this need in a very modest way. It presents the subject in a new perspective. An earnest attempt is made to reveal the critical problems inhibiting the growth of the public sector from a new angle which focusses the spot-light on the economics of development. |
Description: | School of management studies, Cochin University of Science And Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3311 |
Files | Size |
---|---|
Dyuthi-T1285.pdf | (33.10Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/1247 |
Files | Size |
---|---|
Wilson P R 1982.PDF | (552.0Kb) |
Abstract: | Time resolved optical emission spectroscopy is employed to study the expansion dynamics of C2 species in a graphite plasma produced during the Nd : YAG ablation. At low laser fluences a single peak distribution with low kinetic energy is observed. At higher fluences a twin peak distribution is found. It has been noted that these double peak time of flight distribution splits into a triple peak structure at distances >_ 17mm from the target surface. The reason for the occurrence of multiple peak is due to different formation mechanisms of C2 species |
URI: | http://dyuthi.cusat.ac.in/purl/2454 |
Files | Size |
---|---|
Dyuthi-P0315.pdf | (377.4Kb) |
URI: | http://dyuthi.cusat.ac.in/purl/5221 |
Files | Size |
---|---|
Dyuthi T-2256.pdf | (5.469Mb) |
Abstract: | Mangrove forests are the most productive and bio-diverse wetlands on earth. It generate a large amount of litter in the form of leaves, branches, twigs, inflorescence and other debris and provides habitat for diverse flora and fauna of marine and terrestrial origin such as bacteria, fungi, algae, lichens, zooplankton, benthos, birds, reptiles and mammals. These systems act as nursery for many fishes and shellfishes. The other sources may also provide important organic carbon inputs; including allochthonous riverine or marine material, autochthonous production by benthic or epiphytic micro- or macroalgae, and local water column production by phytoplankton. Since mangrove sediments are very complex which receives autochthonous and allochthonous organic matter inputs, the information extracted from the analysis of mangrove sediments is the fingerprint of both natural and human-induced changes. |
URI: | http://dyuthi.cusat.ac.in/purl/5077 |
Files | Size |
---|---|
Dyuthi- T 2140.pdf | (33.15Mb) |
Abstract: | Warships are generally sleek, slender with V shaped sections and block coefficient below 0.5, compared to fuller forms and higher values for commercial ships. They normally operate in the higher Froude number regime, and the hydrodynamic design is primarily aimed at achieving higher speeds with the minimum power. Therefore the structural design and analysis methods are different from those for commercial ships. Certain design guidelines have been given in documents like Naval Engineering Standards and one of the new developments in this regard is the introduction of classification society rules for the design of warships.The marine environment imposes subjective and objective uncertainties on ship structure. The uncertainties in loads, material properties etc.,. make reliable predictions of ship structural response a difficult task. Strength, stiffness and durability criteria for warship structures can be established by investigations on elastic analysis, ultimate strength analysis and reliability analysis. For analysis of complicated warship structures, special means and valid approximations are required.Preliminary structural design of a frigate size ship has been carried out . A finite element model of the hold model, representative of the complexities in the geometric configuration has been created using the finite element software NISA. Two other models representing the geometry to a limited extent also have been created —- one with two transverse frames and the attached plating alongwith the longitudinal members and the other representing the plating and longitudinal stiffeners between two transverse frames. Linear static analysis of the three models have been carried out and each one with three different boundary conditions. The structural responses have been checked for deflections and stresses against the permissible values. The structure has been found adequate in all the cases. The stresses and deflections predicted by the frame model are comparable with those of the hold model. But no such comparison has been realized for the interstiffener plating model with the other two models.Progressive collapse analyses of the models have been conducted for the three boundary conditions, considering geometric nonlinearity and then combined geometric and material nonlinearity for the hold and the frame models. von Mises — lllyushin yield criteria with elastic-perfectly plastic stress-strain curve has been chosen. ln each case, P-Delta curves have been generated and the ultimate load causing failure (ultimate load factor) has been identified as a multiple of the design load specified by NES.Reliability analysis of the hull module under combined geometric and material nonlinearities have been conducted. The Young's Modulus and the shell thickness have been chosen as the variables. Randomly generated values have been used in the analysis. First Order Second Moment has been used to predict the reliability index and thereafter, the probability of failure. The values have been compared against standard values published in literature. |
Description: | Department of Ship Technology, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2877 |
Files | Size |
---|---|
Dyuthi-T0874.pdf | (12.19Mb) |
Abstract: | Fine particles of cobalt ferrite were synthesized by the sol–gel method. Subsequent heat treatment at different temperatures yielded cobalt ferrites having different grain sizes. X-ray diffraction studies were carried out to elucidate the structure of all the samples. Dielectric permittivity and ac conductivity of all the samples were evaluated as a function of frequency, temperature and grain size. The variation of permittivity and ac conductivity with frequency reveals that the dispersion is due to Maxwell–Wagner type interfacial polarization in general, with a noted variation from the expected behaviour for the cold synthesized samples. High permittivity and conductivity for small grains were explained on the basis of the correlated barrier-hopping model |
Description: | J. Phys. D: Appl. Phys. 40 (2007) 1593–1602 |
URI: | http://dyuthi.cusat.ac.in/purl/4350 |
Files | Size |
---|---|
Finite size eff ... e polarization effects.pdf | (975.7Kb) |
Abstract: | Nanoparticles of nickel ferrite have been synthesized by the sol–gel method and the effect of grain size on its structural and magnetic properties have been studied in detail. X-ray diffraction (XRD) studies revealed that all the samples are single phasic possessing the inverse spinel structure. Grain size of the sol–gel synthesized powders has been determined from the XRD data and the strain graph. A grain size of 9 nm was observed for the as prepared powders of NiFe2O4 obtained through the sol–gel method. It was also observed that strain was induced during the firing process. Magnetization measurements have been carried out on all the samples prepared in the present series. It was found that the specific magnetization of the nanosized NiFe2O4 powders was lower than that of the corresponding coarse-grained counterparts and decreased with a decrease in grain size. The coercivity of the sol–gel synthesized NiFe2O4 nanoparticles attained a maximum value when the grain size was 15nm and then decreased as the grain size was increased further. |
Description: | Journal of Magnetism and Magnetic Materials 302 (2006) 190–195 |
URI: | http://dyuthi.cusat.ac.in/purl/4347 |
Files | Size |
---|---|
Finite size eff ... esized NiFe2O4 powders.pdf | (265.1Kb) |
Abstract: | The whale shark (Rhiniodon typus Smith) is an under exploited species and it is mainly caught for its liver oil . The processing of shark fin for rays is reported here . The fins have a high content of rays . The yield of fin rays from undried fins ranged from 0 .53 to 4 .40 percent with maximum ray content in the lower lobe of caudal fin . The physical and chemical characteristics of the rays are reported . The total nitrogen content is about 15 to 16 percent (dry weight basis) |
Description: | FISHERY TECHNOLOGY,Vol. 27, 1990 |
URI: | http://dyuthi.cusat.ac.in/purl/4117 |
Files | Size |
---|---|
Fins and Fin Ra ... Rhiniodon typus Smith).pdf | (258.6Kb) |
Abstract: | This paper describes the first use of polystyrene-supported poly(amidoamine) (PAMAM) dendrimers as heterogeneous basic organocatalysts for carbon–carbon bond formation. Polystyrene-supported PAMAM dendrimers of first, second and third generations have been used as reusable base catalysts in Knoevenagel condensations of carbonyl compounds with active methylene compounds. The reactions proceed in short periods of time and with 100% selectivity. This novel catalyst eliminates the use of aromatic and halogenated solvents, as well as complex purification processes. The catalysts can be recycled ten times. |
URI: | http://dyuthi.cusat.ac.in/xmlui/purl/1966 |
Files | Size |
---|---|
First Exaple of Organocatalysis....pdf | (135.4Kb) |
Abstract: | A general introduction to the problems faced in the shrimp culture due to waste formation and its consequent environmental hazards and production problems of Giant tiger shrimp, Penaeus monodon is highlighted by the author in this thesis. The objective of the present work was to assess the potential of brackish water finfish to improve bottom soil conditions and thereby increase the growth and production of Penaeus monodon. The salient findings of the present study are summarized in chapter 7. This is followed by the references cited in the thesis and list ofpublications originated from the present study. |
Description: | School of Industrial Fisheries, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3379 |
Files | Size |
---|---|
Dyuthi-T1356.pdf | (4.121Mb) |
Abstract: | Elasmobranchs comprising sharks, skates and rays have traditionally formed an important fishery along the Indian coast. Since 2000, Indian shark fishermen are shifting their fishing operations to deeper/oceanic waters by conducting multi-day fishing trips, which has resulted in considerable changes in the species composition of the landings vis- a-vis those reported during the 1980’s and 1990’s. A case study at Cochin Fisheries Harbour (CFH), southwest coast of India during 2008-09 indicated that besides the existing gillnet–cum- hooks & line and longline fishery for sharks, a targeted fishery at depths >300-1000 m for gulper sharks (Centrophorus spp.) has emerged. In 2008, the chondrichthyan landings (excluding batoids) were mainly constituted by offshore and deep-sea species such as Alopias superciliosus (24.2%), Carcharhinus limbatus (21.1%), Echinorhinus brucus (8.2%), Galeocerdo cuvier (5.4%), Centrophorus spp. (7.3%) and Neoharriotta pinnata (4.2%) while the contribution by the coastal species such as Sphyrna lewini (14.8%), Carcharhinus sorrah (1.4%) and other Carcharhinus spp. has reduced. Several deep-sea sharks previously not recorded in the landings at Cochin were also observed during 2008-09. It includes Hexanchus griseus, Deania profundorum, Zameus squamulosus and Pygmy false catshark (undescribed) which have been reported for the first time from Indian waters. Life history characteristics of the major fished species are discussed in relation to the fishery and its possible impacts on the resource |
URI: | http://dyuthi.cusat.ac.in/purl/4951 |
Files | Size |
---|---|
Dyuthi-T2027.pdf | (8.112Mb) |
Abstract: | The article examines the commodity chain trap of marine fishery in Kerala, at both material and value terms, and its ramifications in the globalised fishery chains. The marketing chains both material and value, are very complex in nature since they involve many types of markets and large number of intermediaries and participants. The article also scrutinizes the sensitivity of consumers’ and country’s responses in terms of dietary and hygienic standards relating to seafood trade. In addition, it discusses the devastating effect about the recent stipulations like the US Bio- Terrorism Act and Shrimp anti-dumping duty on the Kerala fishery products |
Description: | Developing Country Studies,Vol 2, No.5, 2012 |
URI: | http://dyuthi.cusat.ac.in/purl/4592 |
Files | Size |
---|---|
Fishery Commodi ... Kerala Marine Fishery.pdf | (626.6Kb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.